ICAPS 2024
Permanent URI for this collectionhttp://repository.kln.ac.lk/handle/123456789/28744
Browse
6 results
Search Results
Item Enhancing methylene blue removal efficiency using rice-husk derived, modified activated carbon via magnetic particle integration(Faculty of Science, University of Kelaniya Sri Lanka, 2024) Sakunthala, K. A. D. D.; Perera, P. L. R. A.; Perera, W. P. R. T.; Premaratne, W. A. P. J.; Liyanage, J. A.The extensive use of synthetic dyes in industries has increased environmental pollution, reducing oxygen levels and sunlight penetration in water bodies. Activated carbon (AC) is widely used for removing contaminants. However, the effective recovery and reuse of absorbents in post-treatment present a challenge. Hence, AC integrated magnetic particles (MAC), is seen as a better and innovative alternative due to its easy recovery and minimal environmental impact. This study focused on producing MAC using rice husk and evaluating its effectiveness in Methylene Blue (MB) removal using isotherm and kinetic studies. To produce AC, rice husks were initially washed with DI water, treated with HCl (5% v/v) for 24 hours, and dried at 383 K. Physical activation was carried out at 400°C for 2 hours. Synthesised AC was then mixed with FeSO4 (FeSO4: DI water =1:7.5) and freshly prepared FeCl3 (FeCl3: DI water = 1:72) mixture, stirred at 60-70°C for 30 min, and adjusted to pH 10 using NaOH (10 M). After mixing for 60 min, mixture was left for 24 hours at room temperature, washed with DI water and ethanol, followed by vacuum filtration and overnight drying at 50°C to yield MAC. Characterization was done using Fourier Transform Infrared Spectroscopy (FT-IR). Proximate analysis was carried out and the yield percentage of MAC was calculated. Batch adsorption studies were conducted to optimize parameters such as initial MB concentration, adsorbent dosage, contact time, and pH, for MB removal. Subsequently, under optimized conditions, isotherm and kinetic experiments were conducted. All experiments were duplicated and performed at room temperature. The FT-IR analysis of MAC revealed distinctive features: additional bands at 635.2 cm⁻¹ and 882.7 cm⁻¹, indicating the presence of stretching and bending vibrations of Fe-O bonds. Additionally, a band at 1105.7 cm⁻¹ suggested potential Fe-O-C interactions, confirming the integration of magnetic particles onto the AC surface. In batch adsorption studies, MAC (0.0212 ± 0.0001 g) had optimal MB removal at pH (7.01 ± 0.01) and an initial concentration of 4 mg/L, following 60 minutes of agitation. Adsorption isotherm analysis illustrated an excellent fitting to the Langmuir model (R2=0.9934), revealing monolayer adsorption on a homogeneous surface, with a maximum adsorption capacity (qmax) of 102.04 mg/g. Kinetic studies indicated that the adsorption process followed a pseudo-second-order reaction (R2 = 0.9884), suggesting chemical sorption as the governing mechanism. In conclusion, this study demonstrated the effective integration of magnetic particles with AC derived from rice husks, which enhances the recoverability of the adsorbent in the post-treatment phase due to its magnetic property. Furthermore, this innovative approach ensures effective MB removal from wastewater, providing an eco-friendly and cost-effective solution that advances wastewater treatment technologies without environmental compromise.Item Assessment of heavy metal contamination in surface water, sediment and paddy soil in CKDu endemic regions: A comparative study in Minipe and Dambagolla, Sri Lanka(Faculty of Science, University of Kelaniya Sri Lanka, 2024) Lakshan, L. M. U.; Sakunthala, K. A. D. D.; Perera, P. L. R. A.; Perera, W. P. R. T.; Liyanage, J. A.; Premaratne, W. A. P. J.Chronic Kidney Disease of unknown etiology (CKDu) is a major health crisis in Sri Lanka, particularly affecting rural agricultural communities in regions such as the Central and Uva provinces. This study investigated the concentrations of heavy metals, alongside various quality indicators, in water, sediment, and paddy soil within CKDu endemic regions of these provinces. The objective is to determine whether toxic heavy metals present in surface water, sediment, and paddy soil correlate with the upraised CKDu incidence in Dambagolla compared to Minipe. Using a stratified random sampling technique, surface water and sediment samples were collected from three locations: Minipe Anicut, Minipe Canal, and Loggal Oya. Eighteen composite sediment samples (six from each location) and thirteen surface water samples (three from Minipe Anicut, two from Minipe Canal, and eight from Loggal Oya) were collected. Additionally, a total of twelve topsoil samples (six from each location) were collected from paddy fields in Minipe and Dambagolla areas in which higher CKDu prevalence was recorded compared to Minipe. Water samples were analyzed for pH, electrical conductivity (EC), hardness, and phosphate using standard methods. Sediment and soil samples were tested for pH, EC, organic matter, potassium, phosphate, and total nitrogen. Heavy metals (Pb, As, Cr, Cd, Ni) were quantified using Inductively Coupled Plasma–Mass Spectrometry (ICP-MS). All analyses were duplicated. Statistical significance across parameters was assessed through ANOVA and Tukey's pairwise comparisons. Water samples from all locations have maintained pH levels within WHO recommendations. Minipe Anicut samples had relatively lower conductivity (141.1±27.27 μS/cm) while having elevated hardness (65.39±7.58 mg/L) and phosphate levels (12.28±9.67 ppm). Pb, Cr, and Cd were not detected in Minipe Anicut, and Cr was absent in Minipe Canal. Arsenic levels, although within WHO standards, were higher than other metals, particularly in Minipe Canal (4.17±0.03 µg/L) and Loggal Oya (5.25±3.89 µg/L). ANOVA showed no significant differences in heavy metal levels among sites (p>0.05). Sediment samples from Minipe Canal had lower levels of Cr (11.93±0.37 mg/kg) Pb (2.52±1.06 mg/kg), As (0.62±0.30 mg/kg), Cd (0.013±0.010 mg/kg), and potassium, resulting in substantially lower conductivity. In Minipe Anicut and Loggal Oya, heavy metal content followed the order Cd < As < Pb < Ni < Cr, with Minipe Anicut showing slightly higher concentrations. Furthermore, paddy soil analysis showed higher organic matter content in Dambagolla (4.16±0.46%) compared to Minipe (1.22±0.15%), while Minipe had higher heavy metal concentrations and potassium content (p<0.05). The results suggest that agricultural activities, natural geological factors, and localized contamination sources influence the water, sediment, and soil quality in the studied areas. Furthermore, findings reveal that heavy metal concentrations in surface water, sediment, and paddy soil were not significantly linked to the higher CKDu prevalence in Dambagolla compared to Minipe, suggesting greater influence from other critical factors, driving CKDu development in this region.Item Evaluation of quality parameters and heavy metals in selected cosmetic products in Sri Lankan market(Faculty of Science, University of Kelaniya Sri Lanka, 2024) De Silva, J. H. I. G.; Premaratne, W. A. P. J.Cosmetic products play a significant role in personal care routines worldwide, including in Sri Lanka. Concerns regarding the quality and safety of products have grown due to the potential presence of harmful chemicals and inconsistent product formulations. This study focuses on the analysis of selected cosmetic products commonly available in the Sri Lankan market, assessing their quality attributes, and detecting possible toxic metal contaminants. Four brands of skin creams sold in Sri Lankan market have been investigated for a period of one year (June 2021-June 2022). All analyses were done in triplicates for each sample. Samples have been selected under three categories, sun creams (S1-S4), moisturizing creams (S5-S8) and whitening creams (S9-S12). These samples were obtained from four brands. pH, Non-volatile matter, water content and toxic metals were analyzed. All physicochemical parameters were analyzed according to the test methods given by the SLSI. Heavy metals were analyzed using ICPMS. Range of pH at 27±2oC in selected creams was (5.7 ± 0.09 to 7.8 ± 0.14). According to the specification for skin creams (SLS743:2021), the acceptable range of pH at 27±2oC in creams is 4.5- 8.0. pH value of all the skin care cream samples were statistically in acceptable pH range. Nonvolatile matter at 105oC percent by mass in selected creams was (9.90 ± 0.08 to 24.90 ± 0.07). According to the specification for skin creams (SLS743:2021), acceptable Non-volatile matter at 105oC, percent by mass (minimum value) of skin creams is 15. Nonvolatile matter of S1, S2, S3, S4, S6, and S7 were 10.6. ± 0.11, 9.5 ± 0.42, 11.2± 0.08, 14.20 ± 0.34, 9.90 ± 0.08 and 11.10 ± 0.06 respectively and all six samples were not complied with the acceptable (minimum) level. The water content percentage by mass in selected creams was (70.40 ± 0.59 to 87.60 ± 0.53). According to the specification for skin creams (SLS743:2021), acceptable Water content, percent by mass (maximum value) of skin creams is 85. The water content of all samples was below the acceptable (maximum) level except S4 sample (87.60 ± 0.53). Some of metal concentrations were tested under metal analysis, Aluminium 9.2 ± 0.18 - 224.9 ± 3.24 mg/kg, Zinc 2.90 ± 0.09 – 19866.7 ± 1423.21 mg/kg, Calcium 88.1 ± 5.2 – 2647.8 ± 87.1 mg/kg, Potassium 15.4 ± 0.16 – 3645.8 ± 4.97 mg/kg, Sodium 142.3 ± 2.9 – 7960.2 ± 845 mg/kg), Molybdenum 0.33±0.01 - 3.09 ± 0.06 mg/kg, Magnesium 9.10 ± 0.04 - 250.00 ± 168.13 mg/kg, Vanadium 0.34 ± 0.01 - 2.41 ± 0.06 mg/kg. Some metals were not detected, and some results were below LOQ level. According to the specification for skin creams and lotions (SLS743:2021), acceptable maximum value of Lead, Arsenic, Mercury, Cadmium concentration in skin creams are 10 mg/kg, 3 mg/kg, 1 mg/kg and 3 mg/kg respectively. As, Cd, Pb, and Hg level were below the recommended limits according to the SLS standard. According to the results obtained from this study, all the tested samples were in acceptable quality and as the recommendation; further research can be conducted to determine the chemical concentrations which can damage the function of skin.Item Assessment of derivative spectrophotometry for analyzing competitive adsorption of brilliant green and methylene blue using multiple coated graphite oxide/sand composite(Faculty of Science, University of Kelaniya Sri Lanka, 2024) Sakalasuriya, D. D.; Perera, P. L. R. A.; Perera, W. P. R. T.; Sakunthala, K. A. D. D.; Premaratne, W. A. P. J.; Liyanage, J. AWastewater from industrial sectors such as paint production and textile processing are often contaminated with multiple dye pollutants. The simultaneous presence of multiple dyes like Brilliant Green (BG) and Methylene Blue (MB) poses significant challenges for treatment technologies. These dyes not only contribute to environmental degradation but also pose significant health risks, including allergic reactions and cancer due to their toxicity and persistence in ecosystems. A major challenge in treating dye mixtures is the accurate identification and quantification of multiple dyes due to overlapping absorption spectra. This research aims to enhance the resolution of spectral data using derivative spectrophotometry, enabling more distinct identification of overlapping dye components. In this study, the competitive adsorption of MB and BG onto multiple coated graphite oxide/sand (MGO/S) composite was examined. The determination of dye concentrations was carried out using first order derivative (1D) spectrophotometry. Kinetic and isotherm evaluations were conducted under optimal conditions: pH 7.0, 0.09 g of M-GO/S, and a contact time of 20 minutes in binary dye systems. The 20-minute contact time was sufficient to reach equilibrium, as extended durations showed no significant change in adsorption results from preliminary experiments. The experiment was triplicated. The equilibrium adsorption of MB and BG dyes onto M-GO/S showed an inverse relationship with their initial concentrations, signifying the competitive adsorption dynamics where the dyes compete for the available adsorption sites. In a binary mixture of 10 mg/L BG and MB, significant peak overlap at 625 nm and 664 nm hinders precise concentration measurement using zero-order spectra. First-order derivative spectrophotometry resolves this by identifying the adsorption peaks of MB at 625.6, and 503 nm, and BG at 443.2, 445.6, 525.6 and 664.2 nm. Simultaneous determination of BG and MB was achieved at 443.2 nm (1D443.2) (R2=0.9982) and 625.6 nm (1D625.6) (R2=0.9958), respectively. The characteristic parameters of regression equation for the 1D method and obtained coefficient of determination for individual BG and MB were also studied. Therefore, the application of derivative spectrophotometry has proven to be an effective method for quantification of simultaneous adsorptions of BG and MB onto multiple coated graphite oxide adsorbent. This technique allows for precise differentiation and quantification of each dye in the presence of the other, enhancing the understanding of their adsorption dynamics. The results demonstrate that derivative spectrophotometry can improve the accuracy and efficiency of multipollutant adsorption studies.Item The role of ascorbic acid in optimizing optoelectronic performances of CdS thin films(Faculty of Science, University of Kelaniya Sri Lanka, 2024) Danansuriya, D. B. U. I.; Hetti Arachchige, K. A.; Manilgama, T. T. D.; Kalingamudali, S. R. D.; Premaratne, W. A. P. J.; Jayathilaka, K. M. D. C.; Wijesundara, L. B. D. R. P.; Kumarage, W. G. C.Cadmium sulfide (CdS), a widely studied (II-VI) group semiconductor, has long captivated the scientific community due to its potential applications in photovoltaic (PV) devices. However, optoelectrical properties of n-CdS, such as flat band potential, and optical band gap, are crucial for enhancing solar cell efficiency. This study explores the tunability of these properties in CdS thin films through chemical bath deposition (CBD) with a mild reducing agent ascorbic acid (C6H8O6). A series of CdS thin films were deposited on fluorine-doped tin oxide (FTO) glass substrates by using various concentrations of ascorbic acid (0, 0.1, 0.01, and 0.001 mol.dm-3). The deposition chemical bath consisted of 0.1 mol.dm-3 cadmium sulfate (CdSO4) and 0.2 mol.dm-3 thiourea (CS(NH2)2) as cadmium and sulfur sources, respectively. The deposition process was conducted at 80 °C for one hour at a pH of 11. Post-deposition, the CdS films were etched in the non-conductive side of the FTO with diluted hydrochloric acid (HCl), followed by annealing at 300 °C for one hour in air. All the electrical measurements were performed in a photoelectrochemical cell comprising a CdS/0.1 mol.dm-3 Na2S2O3/Pt half-cell with an active area of 1 cm². An Ag/AgCl electrode served as the reference for all characterizations. The short-circuit current density (JSC) has shown a significant increase with decreasing ascorbic acid concentration, achieving a 155.6% enhancement with a concentration of 0.001 mol.dm-3 compared to untreated CdS. Conversely, with increasing ascorbic acid concentration the opencircuit voltage (VOC) and the flat band potential (VFB) decreased. The highest reported photocurrent power (VOC×ISC) was observed in films deposited with 0.001 mol.dm-3 ascorbic acid, showing a 150.2% improvement over untreated CdS. Scanning electron microscopy (SEM) analysis revealed that ascorbic acid-treated CdS films exhibited aggregated nanoscale particles, whereas untreated films displayed larger clusters. Consequently, the photocurrent enhancement is attributed to these morphological changes that cause higher effective surface area in the ascorbic-treated CdS thin films compared to the untreated CdS. Furthermore, Mott-Schottky analysis confirmed that all deposited films retained n-type characteristics. This study demonstrates that the electronic properties of n-CdS can be finely tuned through ascorbic acid treatment, making it a promising approach for fabricating thin film solar cells with high light-to-current conversion efficiency. The ability to control and enhance these properties is invaluable for advancing PV applications and achieving higher solar cell performances.Item Risk assessment of toxic heavy metals in Oryza sativa (rice) from CKDu prevalent areas: Dambagolla and Minipe, Sri Lanka(Faculty of Science, University of Kelaniya Sri Lanka, 2024) Yasandhika, K. K. G. N.; Perera, P. L. R. A.; Perera, W. P. R. T.; Premaratne, W. A. P. J.; Liyanage, J. A.Chronic Kidney Disease of unknown etiology (CKDu) has been a significant health issue in North Central region in Sri Lanka. One of the suspected contributing factors to CKDu is the contamination of food crops, particularly rice, with toxic heavy metals. This study assessed the risk associated with toxic heavy metals in rice (Oryza sativa; BG- 300) grown in two CKDu prevalent areas, Dambagolla and Minipe. Despite being only approximately 4 kilometers apart and separated by the Mahaweli River, there is a significant difference in CKDu prevalence. In 2023, Dambagolla reported over 50 CKDu patients, whereas Minipe reported fewer than 10. The objective of this study is to evaluate the concentration of toxic heavy metals in rice samples from these areas and to determine if these concentrations correlate with the incidence of CKDu. Twenty rice samples were collected from each paddy field in Dambagolla and Minipe using a random stratified sampling method. Heavy metal analysis, (lead (Pb), arsenic (As), chromium (Cr), cadmium (Cd), and nickel (Ni)), was conducted using Inductively Coupled Plasma Mass Spectrometry (ICP-MS). All sample analyses were duplicated. The data were analyzed to compare the levels of these metals with the maximum permissible levels (MPL) set by the Codex Alimentarius Commission. Additionally, the Target Hazard Quotient (THQ) levels were evaluated, and statistical evaluation was performed using the two-way ANOVA method. In Minipe, the detected levels of heavy metals were Pb (0.315 ± 0.091 mg/kg), As (0.0504 ± 0.01 mg/kg), Cr (0.735 ± 0.086 mg/kg), Cd (1.071 ± 0.087 mg/kg), and Ni (0.247 ± 0.005 mg/kg). In Dambagolla, the detected levels were Pb (0.291 ± 0.06 mg/kg), As (0.093 ± 0.03 mg/kg), Cr (0.388 ± 0.086 mg/kg), Cd (1.124 ± 0.078 mg/kg), and Ni (2.100 ± 0.017 mg/kg). Among the analyzed metals, the mean concentrations of Cd and Pb exceeded the maximum permissible levels (MPL) set by the Codex Alimentarius Commission in both areas. The Target Hazard Quotient (THQ) indexes indicated significant health risks in both areas. In Minipe, the THQ values for Cr (12.26) and Cd (5.355) exceeded threshold values, suggesting a potential health hazard. In Dambagolla, the THQ values for Cr (4.8653), Cd (1.9442), As (18.73), and Pb (3.000) also exceeded threshold values, indicating a significant health concern. Statistical analysis using two-way ANOVA revealed that the concentrations of As and Ni varied significantly between the two areas (p < 0.05). These findings suggest that the elevated levels of Cd and Pb in rice could be contributing to the higher incidence of CKDu in Dambagolla compared to Minipe. The regular consumption of rice could pose significant health risks, potentially contributing to the prevalence of CKDu in these regions. Further investigation is necessary to identify the sources of these heavy metals and to develop strategies to mitigate their impact on public health.