Science
Permanent URI for this communityhttp://repository.kln.ac.lk/handle/123456789/1
Browse
3 results
Search Results
Item Fabrication of Cu2O homojunction thin films for photovoltaic applications.(International Research Symposium on Pure and Applied Sciences, 2017 Faculty of Science, University of Kelaniya, Sri Lanka., 2017) Kafi, F. S. B.; Jayathilaka, K.M.D.C.; Wijesundera, R. P.; Siripala, W.Environmentally friendly cuprous oxide (Cu2O) is an attractive cost effective material for developing photovoltaic devices due to its astounding properties. Interestingly, the fabrication of low cost Cu2O homojunction devices is possible due to Cu2O is abundant and the ability of forming the p-Cu2O and n-Cu2O thin films using cost effective electrodeposition technique. Indeed, it is necessary to optimize p-n junction devices by varying deposition parameters. Vividly, the pH of the deposition bath controls the quality of the electrodeposited Cu2O thin films. Hence, it is important to optimize the pH value of the bath use for the electrodeposition of n-Cu2O and p-Cu2O films for developing Cu2O based devices. In this study, Cu2O thin film homojunction device was fabricated using a successive deposition of an n-Cu2O film followed by a p-Cu2O film, in two different baths; acetate and lactate respectively. The Cu2O homojunction was fabricated on a Ti substrate by the two-step potentiostatic electrodeposition process. A set of n-Cu2O thin films were electrodeposited on Ti substrate in a three electrode aqueous electrochemical cell containing 0.1 M sodium acetate and 0.01 M cupric acetate at potential of -200 mV vs. Ag/AgCl electrode, bath temperature of 55 °C and the film deposition time of 1 hour at two different pH values of n-Cu2O thin film deposition baths; 6.1 and 6.5. Then to optimize the Cu2O homojunction, Ti/n-Cu2O/p-Cu2O junction was fabricated by consequently electrodepositing p-Cu2O thin film on n-Cu2O film by changing the pH value from 7.0 to 13 of the p-Cu2O thin film deposition bath. The electrochemical bath used for the deposition of p-Cu2O thin films contained 3 M lactic acid, 0.4 M copper sulfate and 4 M NaOH. pH of the deposition baths were controlled by adding NaOH and HCl. Then Ti/n-Cu2O/p-Cu2O/Au structure was fabricated by sputtering Au on the resulted Cu2O homojunction. The highest photoactive film observed for Ti/n-Cu2O/p-Cu2O/Au structure that was fabricated at pH values of 6.1 and 11.0 for n-Cu2O and p-Cu2O deposition baths respectively. The observed VOC and JSC values for the optimum Ti/n-Cu2O/p-Cu2O/Au structure was 344 mV and 1.13 mA/cm2 respectively, under AM 1.5 illumination. The resulted high VOC and ISC values evident for the possibility of fabrication of Cu2O homojunction devices by employing consecutive electrodeposition of an n-Cu2O layer followed by a p-Cu2O layer using the relevant baths at different growth conditions. Promisingly, fabricated Cu2O homojunction may further improved by surface treatments and optimizations, to produce high efficient Cu2O homojunction devices.Item Electrodeposited Cu2O homojunction solar cells: Fabrication of a cell of high short circuit photocurrent(Elsevier, 2016) Wijesundera, R.P.; Gunawardhana, L.K.A.D.D.S.; Siripala, W.A Cu2O homojunction solar cell was fabricated using a consecutive electrodeposition method of deposition of an n-Cu2O film followed by a p-Cu2O film, in two different acetate baths. Both n-type and p-type film growth conditions were optimized separately to yield high photocurrents in a photoelctrochemical (PEC) cell. Further, the resulted bi-layer films were investigated in the PEC for the verification of the formation of the p-n homojunction. In addition, p-Cu2O film surfaces of the bi-layers were sulphided using Na2S and (NH4)2S in order to improve the photoresponse of the homojunction before depositing a Au film for the solar cell device. The structural, morphological and optoelectronic properties of the Cu2O films were investigated using X-ray diffraction (XRD), scanning electron micrographs (SEMs), dark and light current–voltage (I-V) and spectral response measurements and observed that the films are of good quality. Incident photon to current efficiency (IPCE) and I-V characteristics of the solar cell device demonstrated that the Cu2O homojunction can produce a high short circuit current density Jsc. However, the overall conversion efficiency of the device is low due to poor fill factor and Voc. The solar cell characteristics of the structure Ti/n-Cu2O/p-Cu2O/Au were Voc=287.0±0.1 mV, Jsc=12.4±0. 1 mA/cm2, FF=25±2% and η=0.89±0.02%, under AM 1.5 illumination. The record high Jsc value of the device demonstrates the prospect being improved the efficiency of Cu2O homojunction solar cells by optimizing deposition, pretreatment and post treatment processes.Item Potentiostatic electrodeposition of cuprous oxide thin films(Journal of the National Science Council of Sri Lanka, 1996) Perera, L.D.R.D.; Siripala, W.; de Silva, K.T.L.Current-potential scans were used to investigate the electrodeposition of coprous oxide thin films in an acetate bath. We found that a narrow potential domain, from OV vs SCE, is available for the potentiostatic electrodeposition of cuprous oxide thin films and extension of this domain towards more cathodic potentials will result in the co-deposition of copper. These results were further verified by the x-ray diffraction measurements on the thin films formed by the electrodeposition at various electrode potensials. Optical transmission studies revealed that electrodeposited cuprous oxide is a direct band gap semiconductor of 2.0 eV.