Science

Permanent URI for this communityhttp://repository.kln.ac.lk/handle/123456789/1

Browse

Author: search.filters.author.Jayasuriya, K.D.End date: 1999

Search Results

Now showing 1 - 10 of 21
  • Thumbnail Image
    Item
    ITO/n-Cu2O/p-CuxS Thin Film Solar Cell
    (Sri Lanka Association for the Advancement of Science, 1997) Perera, L.D.R.D.; Wijesundera, R.P.; Siripala, W.; Jayasuriya, K.D.; de Silva, K.T.L.; Jayanetti, J.K.D.S.
  • Thumbnail Image
    Item
    A Study of CuInS2 Thin Films for Photovoltaic Applications
    (Proceedings of the Technical Session of Institute of Physics, 1999) Wijesundera, R.P.; Nadesalingam, M.P.; Siripala, W.; Jayasuriya, K.D.; Kalingamudali, S.R.D.; Jayanetti, J.K.D.S.; de Silva, K.T.L.
    Thin films of copper indium disulphide (CuInS2) on Ti Substrate were prepared by annealing potentiastatically electrodeposited Cu-In alloy in H2S gas at 5500 C. Films were characteristised by X-ray diffraction (XRD), scanning electron microscopy (SEM), and spectral response in a polysulphide electrolyte. XRD measurements revealed the formation of the polysrystaline CuInS2 thin films and the abscence of any other phases. SEM showed the formation of crystallites having the size about 0.2 ?m. Variations of spectral response, open-circuit voltage (Voc) and short circuit current (Isc) with annealing in air have been studied. As deposited CuInS2 films exhibit a direct band gap of 1.5 eV, and shows n-type behaviour when used in a Photoelectrochemical (PEC) cell. Heat treatment shows a considerable enhancement of the photoresponse.
  • No Thumbnail Available
    Item
    Computational Study of I-V characteristics of ITO/Cu2 O/Metal junctions, Technical Session of Institute of Physics
    (Processing of the Technical Session of Institute of Physics, 1999) Wijesinghe, W.M.P.L.; Siripala, W.; Jayasuriya, K.D.; Kalingamudali, S.R.D.
    A theoretical model for current-voltage (I-V) characteristics of back-to-back diode systems was developed using the ideal diode equation. A computer model was developed using the language C++ to fit the experimental data to the theoretical equation and to determine the ideality factors and reverse saturation currents of each diode. This model was tested with commercial back-to-back diode systems. The values obtained for the above parameters from the theoretical fits were in very good agreement with the standard values. The experimental I-V characteristics data obtained for fabricated ITO/Cu2O/Metal (Au, Ag and Hg) structures were fitted to the model and values for the relevent parameters were obtained. These values indicate that the fabricated systems are back to back diodes except the ITO//Cu2O/Hg structure. Using this model, a good understanding of I-V characteristics of metal-semiconductor-metal diodes can be gained and thereby the quality of junction devices can be tested.
  • No Thumbnail Available
    Item
    A Home Made Double Slab Pyranometer for Irradiance Measurements
    (Proceedings of the 44th Technical Session of the Sri Lanka Association for the Advancement of Science (SLAAS), 1988) Punyasena, M.A.; Jayasuriya, K.D.
  • No Thumbnail Available
    Item
    ITO/ u-Cu2O/ p-Cu2S thin film solar cell
    (Srilanka association for the advancement od science proceedings of 53rd Anuual Session., 1997) Perera, L.D.R.D.; Wijesundara, R.; Jayasuriya, K.D.; de Silva, K.T.L.; Jayanetti, J.K.D.S.
  • No Thumbnail Available
    Item
    Construction of a Near Ideal Nanoammeter
    (1998) Wijesundera, R.P.; Kalingamudali, S.R.D.; Jayasuriya, K.D.
    A near ideal ac/dc nanoammeter was constructed using two operational amplifiers (op-amp) and a voltmeter. Small currents were converted into a voltage by the first op-amp and this was amplified into a larger voltage by the second op-amp. The amplified voltage was measuredby the voltmeter. The constructed meter has 10 and 100 nA ranges for the dc current measurements and 100 nA range for the ac current measurements.All the ranges were calibrated using a digital picoammeter. As compared to commercially available nanoammeters with similar features this meter has higher advantages such as almost zero internal resistance and negligible operating bias current. The construction cost of the meter is very low compared to a commercial ac/dc nanoammeter.
  • Thumbnail Image
    Item
    Study of Sulphidation of Electrodeposited Cu2O Thin Films for Solar Cell Applications
    (1998) Siripala, W.; Wijesundera, R.P.; Perera, L.D.R.D.; Jayasuriya, K.D.
    Cuprous oxide (Cu20 ) layers were potentiostatically electrodeposited on glass/ITO substrates and then they were partially sulphided using Na2S and H2S. Resulting layers were used to fabricate ITO/n-Cu20/p-CuxS thin film solar cells. Spectral response measurements showed that the cell structure exhibits both n- and p-type behavior. Sulphidation of Cu20 does not produce CuxS thick layers adequate for efficient heterojunction solar cell, but improved the photovoltaic activity. The best device fabricated shows V? = 240 mV and Isc= 1.6mA/cm2 under AM 1 artificial illumination.
  • No Thumbnail Available
    Item
    Surfactant assisted ball-milling of barium ferrite
    (IEEE Transactions on Magnetics, 1994) Jayasuriya, K.D.; Wu, E.; Kaczmarek, W.A.; Campbell, S.J.
    The effects of wet-milling barium ferrite in the presence of cationic or anionic surface active substances have been investigated by X-ray diffraction and Mossbauer spectroscopy measurements. Evidence for superparamagnetic relaxation of fine particles, both in the surfactant assisted ball-milled samples and in samples dry-milled in air is obtained from the room temperature and 4.2 K Mossbauer spectra. The similarity between samples milled at pH 3 with the cationic or anionic surfactants is due to electrostatic interactions of the surfactants' hydrocarbon groups with the positively charged barium ferrite surface
  • No Thumbnail Available
    Item
    A Mössbauer effect study of barium ferrite ball-milled in air
    (Hyperfine Interactions, 1994) Jayasuriya, K.D.; Kaczmarek, W.A.; Wu, E.; Campbell, S.J.
    The effects of dry-milling BaFe12O19 in air for periods of 190, 360, 590, 690 and 1000 h have been investigated by X-ray diffraction and M�ssbauer effect measurements. The sizes of the BaFe12O19 particles decrease on milling, as expected, although a partial decomposition of BaFe12O19 to ?-Fe2O3 is found to take place on extended milling (1000 h). The room temperature M�ssbauer spectra are consistent with superparamagnetic relaxation associated with the fine BaFe12O19 and ?-Fe2O3 particles. The X-ray diffraction patterns of all the milled samples exhibit features indicative of a disordered structural state, consistent with the nanoscale particles and a nanostructured state.
  • No Thumbnail Available
    Item
    A Mössbauer study of ball-milled Co?Fe?Si?B: II: with surfactants
    (Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms, 1993) Jayasuriya, K.D.; Campbell, S.J.; Calka, A.; Jing, J.
    The use of a range of organic surface active substances in the ball milling of Co?Fe?Si?B has been studied by X-ray diffraction and M�ssbauer effect measurements. Effects characteristic of superparamagnetic relaxation of the magnetic moments are observed in the M�ssbauer spectra of samples milled with either an anionic or a cationic surfactant. This behaviour is linked with the decreased particle size and high shape homogeneity of surfactant-aided milled samples compared with the amorphous powders resulting from standard dry milling. Impurity iron-oxide phases are also found to occur in samples milled in the presence of surfactants.