Browsing by Author "Namawardana, D. G. K. K."

Filter results by typing the first few letters
Now showing 1 - 2 of 2
  • No Thumbnail Available
    Item
    Electrodeposited metal sulfide thin films for gas sensing applications
    (4th International Research Symposium on Pure and Applied Sciences, Faculty of Science, University of Kelaniya, Sri Lanka, 2019) Namawardana, D. G. K. K.; Wickramathilaka, P. A. K. Y.; Atapattu, H. Y. R.; De Silva, D. S. M.
    Quantitative measurements of gases are based on a variety of physical or chemical principles. Among them semiconductor gas sensors are best candidates for the development of commercial gas sensors due to their higher specificity and sensitivity. They are mainly based on metal oxide and metal sulfide materials. Due to certain drawbacks of metal oxides, metal sulfides are extensively investigated as novel gas sensing materials. In this study ZnS and CdS were investigated for their gas sensing ability. Both types of thin films were fabricated by electrodeposition using a three electrode electrolytic system consisted of a fluorine doped tin oxide glass substrate (1×3 cm2) as working electrode and a high purity carbon as counter electrode. An aqueous electrolyte containing CdCl2 (0.10 mol/L) and Na2S2O3 (0.01 mol/L) precursors were used for the electrodeposition of CdS material and aqueous electrolyte containing ZnCl2 (0.10 - 0.05 mol/L) and Na2S2O3 (0.01 - 0.05 mol/L) precursors were used for electrodeposition of ZnS material. The CdS depositions were carried out in the cathodic deposition potential (CDP) range of 0.65 to 0.70 V vs. saturated calomel electrode and pH range of 1.5 to 2.0 at a temperature of 55 °C for 30 minutes. The ZnS depositions were carried out in the CDP range of 0.70 to 1.10 V vs. Ag/AgCl reference electrode and pH range of 4.0 to 3.5 at a temperature of 30 °C for 90 minutes. Both types of thin films were characterized for their crystalline structure, surface morphology, and elemental composition by using the techniques of X-ray diffraction spectroscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy respectively and were exposed to various gases namely; NO2, H2S, and LPG. CdS thin films grown at CDP of 0.67 V and pH of 1.5 and ZnS thin films grown at CDP of 1.05 V and pH of 3.7 were found to have notable gas sensing properties. CdS has shown highest resistance variation of 1.2 Ω towards H2S with respect to the initial resistance of 36.0 Ω and ZnS has shown highest resistance variation of 2 Ω with respect to the initial resistance of 26.2 Ω when exposed to NO2 gas at 30 oC. Both CdS and ZnS thin films showed resistance variation of 1.1 Ω and 0.6 Ω towards LPG respectively at 30 oC.
  • No Thumbnail Available
    Item
    Fabrication of inverted organic solar cells on stainless steel substrate with electrodeposited and spin coated ZnO buffer layers
    (Journal of Polymer Engineering, 2022) Namawardana, D. G. K. K.; Wanigasekara, R. M. G.; Wanninayake, W. T. M. A. P. K.; Jayathilaka, K. M. D. C.; Wijesundera, R. P.; Siripala, W.; Malik, M. I.
    Polymer based organic solar cells (OSCs) are of tremendous interest as suitable candidates for producing clean and renewable energy in recent years. In this study, inverted OSCs on stainless steel (SS) substrate with zinc oxide (ZnO) as the electron selective transport layer (ESTL), are investigated, occupying bulk heterojunction blend of regioregular poly(3-hexylthiophene) (P3HT) and phenyl- C61-butyric acid methyl ester (PCBM) as the active material and poly-(4,3-ethylene dioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) as the hole transport layer (HTL). The device structure is SS/ZnO/P3HT:PCBM/PEDOT:PSS/Au. ZnO films are prepared by spin coating and electrodeposition techniques, followed by annealing under ambient conditions. The insertion of ZnO layer between the SS substrate and active layer has improved short-circuit current ( Jsc), open-circuit voltage (Voc), fill factor (FF), and power conversion efficiency (PCE) compared to those of the reference cell without ZnO layer, achieving the highest efficiency of 0.66% for the device with spin coated ZnO from sol–gel technique. This enhancement can be attributed to the effective electron extraction and the increased crystallinity of ZnO after annealing treatments at higher temperatures as further confirmed by X-ray diffraction (XRD) and scanning electron microscope (SEM) analyses.