Browsing by Author "Fernando, W.T.R.S."

Now showing 1 - 3 of 3

Comparison of the properties of CZTS semiconductor films grown by sequential and single step electrodeposition techniques
(Faculty of Science, University of Kelaniya, Sri Lanka, 2020) Fernando, W.T.R.S.; Jayathilaka, K.M.D.C.; Wijesundera, R.P.; Siripala, W.
Cu2ZnSnS4 (CZTS) is a promising semiconductor material suitable for application in low-cost and environmentally friendly thin film solar cells due to its superior optoelectronics properties. It is a perfect absorber material due to its high absorption coefficient (>10-4 cm-1 ) and direct optical bandgap (1.4-1.5 eV). Among the CZTS preparation techniques, electrodeposition is an attractive technique because of its simplicity, low cost and easy process controlling capability. In this investigation, a comparative study on CZTS films grown by two different techniques, namely, sequential electrodeposition and single step electrodeposition, has been carried out. Electrodeposition of Cu, Sn and Zn stack layers followed by sulphurisation with H2S is one of CZTS growth techniques. In this study, growth parameters of sequentially electrodeposited CZTS were optimized to obtain best photoactive CZTS thin films. Electrodeposition parameters of Cu, Sn and Zn have been obtained using voltammograms. Cu thin film was electrodeposited on Mo substrate at –0.89 V vs Ag/AgCl in an electrochemical cell containing 0.4 M CuSO4, 3 M lactic acid and NaOH at pH 11. Deposition of Sn thin film on Mo/Cu electrodes was carried out at -1.2 V vs Ag/AgCl in an electrochemical cell containing 0.055 M, 2.25 M NaOH and 8 ml of sorbitol. Zn thin film was electrodeposited on Mo/Cu/Sn at -1.2 V vs Ag/AgCl in an electrochemical cell containing 0.2 M ZnSO4. In order to grow CZTS, Mo/Cu/Sn/Zn thin films were annealed at 550 oC for 60 min in H2S. In the single step electrodeposition, CZTS thin films on Mo substrate were potentiostatically electrodeposited at -1.05 V vs Ag/AgCl for 40 min in a three electrode electrochemical cell containing 0.02 M copper (II) sulfate pentahydrate (CuSO4·5H2O), 0.01 M zinc sulfate heptahydrate (ZnSO4·7H2O), 0.02 M tin sulfate (SnSO4) and 0.02 M sodium thiosulfate (Na2S2O3) at room temperature. 0.2 M tri-sodium citrate (C6H5Na3O7) was used as the complexing agent and tartaric acid (C4H6O6) was used as the pH control solution. The pH of the bath was maintained at 5. The Ag/AgCl and platinum electrodes were used as the reference and the counter electrodes respectively. Then samples prepared were annealed at 550 oC for 30 min in H2S. CZTS films grown by two techniques were characterized using X-ray diffraction, reflectance, dark and light I-V, spectral response and C-V measurements in a PEC containing 0.1 M sodium acetate. Reflectance measurements reveal that the band gap energy of the films is 1.45 eV and I-V and spectral response measurements reveal that CZTS thin films were photoactive and p-type. The results obtained revealed that high quality photoactive CZTS can be prepared using both techniques. However, I-V and spectral response characteristics revealed that photoactive properties of CZTS thin films prepared by single step electrodeposition technique are superior in comparison to sequentially electrodeposited thin films.
Fabrication of CZTS/Cu2O Solar Cell.
(19th Conference on Postgraduate Research, International Postgraduate Research Conference 2018, Faculty of Graduate Studies,University of Kelaniya, Sri Lanka, 2018) Fernando, W.T.R.S.; Jayathileka, K.M.D.C.; Siripala, W.; Wijesundera, R.P.
Cu2ZnSnS4 (CZTS) and Cu2O are two promising materials for application in low-cost and environmentally-friendly thin film solar cells due to their optoelectronic properties. Among the various growth techniques available for CZTS and Cu2O, electrodeposition is an attractive technique because of its simplicity, low-cost and easy to control the properties of the deposits. In order to grow CZTS on Mo substrate, Cu thin film was electrodeposited on Mo substrate at –0.89 V vs Ag/AgCl reference electrode (RE) in an electrochemical cell containing 0.4 M CuSO4, 3 M lactic acid and NaOH at pH of 11. Deposition of Sn thin film on Mo/Cu electrodes was carried out at -1.2 V vs Ag/AgCl RE in an electrochemical cell containing 0.055 M SnCl2, 2.25 M NaOH and 8 ml of sorbitol. Zn thin film was electrodeposited on Mo/Cu/Sn at -1.2 V vs Ag/AgCl RE in an electrochemical cell containing 0.2 M ZnSO4. In order to form CZTS material on Mo substrate, Mo/Cu/Sn/Zn thin film electrodes were annealed at 55 °C for 60 min in H2S. In order to fabricate CZTS/Cu2O heterojunction, n-Cu2O thin film was potentiastatically electrodeposited on Mo/CZTS at -0.52 V vs Ag/AgCl RE in electrochemical cell containing 0.45 M CuSO4, 3.0 M lactic acid and 4.0 M NaOH. pH of the bath was adjusted to 9.3 by adding NaOH and the temperature of the bath was maintained at 60 °C. In order to make front contact to the device, thin Au spots (2×2 mm2) were deposited on Cu2O by using the sputtering technique. Materials and device were characterised using XRD, SEM, spectral response, C-V and I-V measurements. In this preliminary study, device exhibited open circuit voltage (VOC) of 200 mV and short circuit current density (JSC) of 0.75 mA cm-2. This result is encouraging since CZTS/Cu2O heterojunction haven’t been reported in the literature. It is planning to improve photoactivity of the device by employing pre and post treatments (annealing and surface treatments).
Growth of CuZnS thin films by sequential electrodeposition and sulphurisation
(Faculty of Science, University of Kelaniya, Sri Lanka, 2016) Fernando, W.T.R.S.; Jayathilekea, K.M.D.C.; Wijesundera, R.P.; Siripala, W.
Copper Zinc Sulphide (CuZnS) is a promising new absorber material for solar cell applications. Indeed, this material is very attractive for low cost device applications due to abundance and low cost of the staring materials. Very recently, a CuZnS based solar cell with In2S3 window material has been reported having Voc of 0.41 V, Jsc of 10.6 mA/cm2, FF of 45% and  of 1.94%. This initial finding has proven the possibility of developing this material as a solar energy material. Among the CuZnS preparation techniques, electrodeposition is an attractive technique because of its simplicity, low cost and possibility of making large area thin films. In this study, possibility of growth of CuZnS thin films by sulphurisation of electrodeposited Cu and Zn stack layers using S powder has been investigated. Cu thin film was electrodeposited on Ti substrate at –700 mV Vs Ag/AgCl for 15 min in an electrochemical cell containing 0.05 M sodium acetate and 0.005 M cupric acetate. Deposition of Zn thin film on Ti/Cu electrodes was carried out at -1.2 V Vs Ag/AgCl for 1 min in an electrochemical cell containing 0.2 M ZnSO4. Deposition parameters of Cu and Zn have been obtained by voltammograms. Set of identical Ti/Cu/Zn thin film electrodes having Cu/Zn ratio of 3.2 were prepared by maintaining the respective Cu and Zn thin film deposition durations for studying the sulphurisation process. In order to grow CuZnS, Ti/Cu/Zn thin film electrodes were annealed at different temperatures (400 oC, 450 oC, 500 oC, 550 oC and 600 oC) with different S contents (10 mg, 20 mg, 30 mg, 40 mg and 50 mg) for a duration of 60 min. CuZnS thin films were characterized using dark and light current voltage measurements in a PEC containing 0.1 M sodium acetate to obtain the best sulphurisation condition. Dark and light I-V characteristics revealed that the films annealed at 600 oC with the S content between 10 to 20 mg exhibits photoactivity. Further, photocurrent was always cathodic confirming the formation of p-CuZnS thin films. It was revealed in this preliminary investigation that the best photoactive films could be produced when films are annealed at 600 oC for 60 min in 20 mg S content. We have found, that photoactive p-CuZnS thin films can be grown by employing the technique of annealing electrodeposited Cu and Zn stack layers using S powder. Cu/Zn ratio of the stack layers could be the crucial parameter in determining the structure, conductivity type and resistivity of CuZnS films and therefore the methodology developed in this study could be further investigated, in order to develop the material for wider applications.